Tiling your living room, bathroom, or kitchen is a part of home renovation project that gives your home a customized look that addresses your tastes and preference. Tiles have ability to improve the market value of your home. However, it will depend on the type of flooring material that is selected. The materials may range from wood laminate, carpet, or tile floors. These materials have their pros and cons. Therefore, it is important to choose one that addresses your needs. The procedure of custom tile flooring may seem to be a difficult task especially when you are doing it yourself. Nevertheless, with research and guidance from an expert you can do it successfully.
After identification of perfect flooring materials, the next step is to prepare your floor or wall. Old tiles should be replaced with cement backer board that will support new tiles. You should install a waterproof membrane to protect the backer board from being damaged by water. The waterproof membrane can be applied by use of a brush or a roller.
New tiles should be installed when the floor is clean and dry. Before purchasing the flooring material, you should measure the dimensions and calculate the size and number of material that you need during the tiling process. Ensure you purchase an excess of ten percent of the material to replace those that are likely to be damage during the installation process. You can consult an expert during the installation process.
Begin with the floor if you are tilling both the floor and the wall. This will minimize potential problems and present an opportunity to cut the material to fit your design. After identifying a vertical starting point, install a level board that runs from the right bottom end to the right top end. This mark will provide the base for installing the initial layer of flooring material.
With the aid of a drill or a mixing paddle, prepare a thin-set-mortar that is suitable for your flooring materials. This step is the easiest since the manufacturers guidelines are labeled on the package. You should stir the mixture until a consistence similar to creamy peanut butter is achieved. The mixture is applied on the particular floor prior to laying the tiles.
You should aim at achieving uniform layered tiles after the installation procedure. This will be possible when you mark a starting point and lay the materials while using the point as reference. Tiles that do not fit ought to be trimmed.
The final stage is called grouting. It is done after the installation process. The materials are given twenty-four hours to set in properly. Mix the grout according to the manufactures instruction indicated on the package. Apply the grout in a sweeping motion and concentrate on the joints.
After identification of perfect flooring materials, the next step is to prepare your floor or wall. Old tiles should be replaced with cement backer board that will support new tiles. You should install a waterproof membrane to protect the backer board from being damaged by water. The waterproof membrane can be applied by use of a brush or a roller.
New tiles should be installed when the floor is clean and dry. Before purchasing the flooring material, you should measure the dimensions and calculate the size and number of material that you need during the tiling process. Ensure you purchase an excess of ten percent of the material to replace those that are likely to be damage during the installation process. You can consult an expert during the installation process.
Begin with the floor if you are tilling both the floor and the wall. This will minimize potential problems and present an opportunity to cut the material to fit your design. After identifying a vertical starting point, install a level board that runs from the right bottom end to the right top end. This mark will provide the base for installing the initial layer of flooring material.
With the aid of a drill or a mixing paddle, prepare a thin-set-mortar that is suitable for your flooring materials. This step is the easiest since the manufacturers guidelines are labeled on the package. You should stir the mixture until a consistence similar to creamy peanut butter is achieved. The mixture is applied on the particular floor prior to laying the tiles.
You should aim at achieving uniform layered tiles after the installation procedure. This will be possible when you mark a starting point and lay the materials while using the point as reference. Tiles that do not fit ought to be trimmed.
The final stage is called grouting. It is done after the installation process. The materials are given twenty-four hours to set in properly. Mix the grout according to the manufactures instruction indicated on the package. Apply the grout in a sweeping motion and concentrate on the joints.
About the Author:
Ainsley G. Zaveri is a flooring specialist who helps individual homeowners make the best choices in getting their home flooring done economically. If you are interested in learning more about Custom Tile Flooring he recommends you check out kmfloorsinc.com
No comments:
Post a Comment