Personal hygiene is enhanced when an individual uses the bathroom. This makes it an essential part of any house. However, its continuous utilization over a long period results in deposition of scam that can be difficult to deal with. This makes the appearance of tub unpleasing, and in this case, engaging in tub refinishing Springfield MA becomes a mandatory thing to carry out.
To start with, an individual is supposed to clean and scrape the entire tub surface. An appropriate tool for the activity is the single blade scrapper. The tool works best in scrapping and is usually stoked in some supplies tore in Springfield MA. When scraping, ore emphasis needs to be given to the site around the overflow section. When there is rust, it can always be dealt with using a rust removal chemical.
The next thing to do is to remove all the caulking. In most bathtubs, silicone and rubber caulking are used in the quest of making the tub watertight. The caulking has to be removed from all the edges of tub and the surrounding tile as well. This will give the individual an opportunity to perform a good job on the tub. After doing, this, water should be used to rinse thoroughly everything.
The next thing to do involves etching the surface. The solution used here is the etching cream. This solution is commonly used in cleaning tubs. By the use of a brush, evenly apply the etching cream on the entire surface. The cream has to be left for bout ten minutes in a bid to efficiently settle. After that, a sponge will come in handy for washing it out. Technicians advise that this need to be carried out starting from the outside part to the inner part. A compressor should then be utilized for getting rid of moisture.
When the tub is completely dry, the sanding part of it can now kick off. Sanding enables it to be as smooth as required for resurfacing. Before you begin, all dents, chips, and defects need to be filled using speed filler. After that, you begin sanding with a dry sand paper followed by a wet one. The wet paper plays a key role in removing all choky residues that may have been left after etching.
It is essential to cover up the surrounding surface which includes walls and the floor. This can be achieved by the use of tapes. The sink, mirror, and cabinet are highly susceptible to damage if they are not well covered. The drain of the tub should also be covered to prevent chemicals from clogging it. The tub surface is then sprayed with alcohol while putting on protective gears such as gloves.
The individual is then expected to apply two layers of primer coat and three layers of acrylic top coat. Be sure to wait thirty minutes between each coat. Duration of one day is given to for tub to dry completely. After that, it will be ready for use. The surface should be cleaned with soap and water before any person takes a bath in it.
Reglazing is an affordable way of making the tub appears brand new. If you find it difficult to do it yourself, finding a technician is recommended. Luckily, the city of Springfield MA has a lot of similar service providers. The new appearance will always make the bathroom elegant.
To start with, an individual is supposed to clean and scrape the entire tub surface. An appropriate tool for the activity is the single blade scrapper. The tool works best in scrapping and is usually stoked in some supplies tore in Springfield MA. When scraping, ore emphasis needs to be given to the site around the overflow section. When there is rust, it can always be dealt with using a rust removal chemical.
The next thing to do is to remove all the caulking. In most bathtubs, silicone and rubber caulking are used in the quest of making the tub watertight. The caulking has to be removed from all the edges of tub and the surrounding tile as well. This will give the individual an opportunity to perform a good job on the tub. After doing, this, water should be used to rinse thoroughly everything.
The next thing to do involves etching the surface. The solution used here is the etching cream. This solution is commonly used in cleaning tubs. By the use of a brush, evenly apply the etching cream on the entire surface. The cream has to be left for bout ten minutes in a bid to efficiently settle. After that, a sponge will come in handy for washing it out. Technicians advise that this need to be carried out starting from the outside part to the inner part. A compressor should then be utilized for getting rid of moisture.
When the tub is completely dry, the sanding part of it can now kick off. Sanding enables it to be as smooth as required for resurfacing. Before you begin, all dents, chips, and defects need to be filled using speed filler. After that, you begin sanding with a dry sand paper followed by a wet one. The wet paper plays a key role in removing all choky residues that may have been left after etching.
It is essential to cover up the surrounding surface which includes walls and the floor. This can be achieved by the use of tapes. The sink, mirror, and cabinet are highly susceptible to damage if they are not well covered. The drain of the tub should also be covered to prevent chemicals from clogging it. The tub surface is then sprayed with alcohol while putting on protective gears such as gloves.
The individual is then expected to apply two layers of primer coat and three layers of acrylic top coat. Be sure to wait thirty minutes between each coat. Duration of one day is given to for tub to dry completely. After that, it will be ready for use. The surface should be cleaned with soap and water before any person takes a bath in it.
Reglazing is an affordable way of making the tub appears brand new. If you find it difficult to do it yourself, finding a technician is recommended. Luckily, the city of Springfield MA has a lot of similar service providers. The new appearance will always make the bathroom elegant.
About the Author:
For expert tub refinishing Springfield MA customers can rely on our excellent service. Take a tour of the following website right now at http://www.refinishingwizards.com.
No comments:
Post a Comment